Solution Partner for the integration of products for SIEMENS emission gas analyzers.
Development and implementation of complete systems and solutions for the supply, installation, start-up, maintenance and calibration of Siemens gas analyzers for measuring pollution parameters, according to the requirements established in the current legislation.
Siemens ULTRAMAT 23 is an emission gas analyzer that can simultaneously measure up to four different compounds (3 IR+O2). The measuring principle is based on absorption by infrared radiation. The gases most frequently measured are SO2, NO, CO, CO2, CH4, O2, SH2. It has a QAL1 certificate.
ULTRAMAT 6 is an analyzer for complex applications that complies with the strictest requirements of reliability and quality of emission. The ULTRAMAT 6 can measure four active compounds by infrared and ULTRAMAT 6F two. The air-tight division of the electronic and physical parts when the equipment is being used guarantees a long working life in hostile environmental conditions. Compounds measured: CO, CO2, NO, SO2, CH4. High selectivity and sample cells easy to clean. It has a QAL1 certificate.
SIPROCESS UV600 is an ultraviolet gas analyzer that can measure three compounds at the same time. It is adequate for extremely selective measurements of NO, with very small measuring ranges; it is also adequate for gases sensitive to UV radiation such as NO, NO2, SO2 and H2S. The analyzer is equipped with state-of-the-art software and technology, with the interfaces needed for remote monitoring from a network and for connection to process control systems. It does not need a NO2 converter. Insensitive to interferences by H2O and CO2. Long working life of the UV source. Measurement of NO in very small concentrations (10 ppm). It has a QAL1 certificate.
The analyzer OXYMAT 6 uses the paramagnetic method of alternate pressure to measure oxygen. This guarantees an absolute linearity and enables the parametrization of very small measuring ranges, from 0-0,5% (detection limit: 50 ppm) to 0-100 % or even 99.5-100% with only one device. The detecting unit is not in contact with the sample, which enables the use of the equipment under harsh conditions and guarantees a long working life. Zero physically suppressed by the appropriate choice of reference gas for the control of air purity or decomposition. Open architecture of interfaces (RS 485, RS 232, PROFIBUS). It has a QAL1 certificate.
SIPROCESS GA700 ULTRAMAT 7
ULTRAMAT 7 has great selectivity and accuracy in measuring complex gas mixtures, as well as reduced maintenance costs thanks to the easy cleaning o the measuring chamber. The analyzer is equipped with a preventive maintenance function that alerts in advance when the next maintenance must take place. Gases measured: CO, CO2, SO2, NO, CH4, C2H4, N2O, NH3. High selectivity. Easy handling. Prepared for Industry 4.0.
MAXUM EDITION II
This chromatograph is used in all the fields of chemistry, in refineries and oil processing plants. This equipment has been specially developed for harsh environments, to be used online at process level. A MAXUM edition II can do the work of several conventional chromatographs. Low exploitation cost: the flexible design of the oven optimizes air and energy consumption in the analytical solution. Versatility thanks to several kinds of detectors: FID, TCD, FPD, PDD (mode HID, PID y ECD) and multidetectors. Touch handling, easy and intuitive, with a large color screen. Powerful software for improved analysis results.
It is SIEMENS's smallest online gas chromatograph, protected against explosion. The analysis module, inside a case with flameproof enclosure, contains all it needs to detach and detect all the compounds in a measurement. Detectors of thermal conductivity (8 TCD cells maximum). Easy remote monitoring with Windows-based software and Ethernet communication. Analysis of natural gas and heating power.
The analyzer FIDAMAT 6 uses a FID (flame ionization detector) as the method for measuring total hydrocarbons. It can be used for measuring traces of hydrocarbon in ultrapure gas and for the total measuring of hydrocarbons in presence of corrosive gas. The adjustable high temperature for the route of the sampling gas and the detector ensure that samples with a high boiling point can be measured, as well as hydrocarbons in high concentrations of water steam up to 100%. Very low sensitivity to crossed interferences. Low consumption of oxidizer. Little influence of the oxygen in the value measured. Warning and failure alerts in case of failure of combustible gas, flame, pump or filter.
The design of Siemens' LDS 6 analyzer opens new possibilities for the control of processes and emissions. It combines a compact structure and a user-friendly design. It is an analyzer for on-site direct measuring of the process gas. It can measure the following compounds: O2, NH3, HCl, HF, H2O, CO, CO2. It allows the simultaneous measurement of two compounds. It has a QUAL1 certificate for NH3, HCl and H2O.